mcarterbrown.com  

Sidearms Bring on the Pistols! From Splatmasters to modern day semi-auto pistols.

Reply
 
Thread Tools Search this Thread
Old 03-04-2011, 01:38 AM   #1 (permalink)
Active Member
 
leen_iz_meen's Avatar
 
Join Date: Feb 2011

delta 68 doesnt shoot semi auto...HELP

hey there guys or gals.....i just aquired a delta 68 its shoots only single shot.id have to recock it after every shot.i removed the bolt and bottom assembly and noticed its missing the recoil pad (large oring). could this be the culprit?.....any suggestions....please help....its a sweeet pistol id like to keep her.....thankx much
leen_iz_meen is offline   Reply With Quote
Old 03-04-2011, 01:50 AM   #2 (permalink)
Official LL5 Dolphin-Dive
 
PistolRogue's Avatar
 
Join Date: Jan 2009
Location: Jackson, NJ
Send a message via AIM to PistolRogue

The bumper shouldn't be the cause of a failure to recock but it can help to prevent the hammer from mushrooming so it's a good idea to replace it. I'd try replacing the hammer o-ring and if that doesn't work, replace the sear.
__________________
Jay AKA Rogue Reservoir Dogs Scenario Paintball Team- Our $#&* is RIGOROUS!
My Gear For SALE!
Check Out My Mod Threads : Pirate DSG - SA17 Mods - Simple/Cheap/Free TPX Mods - The 'Big Damn Hero' DRV
FEEDBACK
PistolRogue is offline   Reply With Quote
Old 03-04-2011, 12:23 PM   #3 (permalink)
Active Member
 
leen_iz_meen's Avatar
 
Join Date: Feb 2011

ill try both suggestions....where can i get parts for the delta 68 pistol?
leen_iz_meen is offline   Reply With Quote
Old 03-04-2011, 01:42 PM   #4 (permalink)
the proper use of .50cal
 
Redcon-5's Avatar
 
Join Date: Oct 2008
Location: Turlock, Ca

You can find Delta 68 parts kits on ebay, but in truth I just take mine down to my local paintball store and they can normally match up any o-ring, they are spyder clones for the most part.
__________________
"You can't be a real country unless you have a beer and an airline. It helps if you have some kind of football team, or some nuclear weapons, but at the very least you need a beer" Frank Zappa
Redcon-5 is offline   Reply With Quote
Old 03-04-2011, 02:31 PM   #5 (permalink)
Active Member
 
leen_iz_meen's Avatar
 
Join Date: Feb 2011

orings i have some on hand.what about other internal parts ....sear?
leen_iz_meen is offline   Reply With Quote
Old 03-04-2011, 08:10 PM   #6 (permalink)
MCB Member
 
agentSmith's Avatar
 
Join Date: Apr 2006
Location: Michigan

The bumper also helps keep the mainspring from bending sideways.

Usually pistols of this type have to be cocked to pierce the co2 or it will gas out because of the hammer holding the cupseal open. If the pistol can be recocked and shot again, then it's likely that the spring from the piercepin block to the nose of the cupseal is way too strong.

The stuff in this thread about tuning the springs of a zeus apply to the delta68 as well:

zeus type spring tuning

Hope that helps too!
Rob
__________________
PISTOLERO:
We play Pistol and we encourage the Few despite the discouragement of the Many.


agentSmith is offline   Reply With Quote
Old 03-05-2011, 12:10 AM   #7 (permalink)
Banned
 
Join Date: Oct 2006

was the bumper in front of the hammer and stuck inside the gun now?
heinous is offline   Reply With Quote
Old 03-05-2011, 04:48 AM   #8 (permalink)
Active Member
 
leen_iz_meen's Avatar
 
Join Date: Feb 2011

i changed the oring on the hammer its shooting darts!!!...thankx everyone
leen_iz_meen is offline   Reply With Quote
Reply

  mcarterbrown.com » Paintball » The Armory » Sidearms

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Forum Jump


All times are GMT -4. The time now is 02:26 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO
© MCB Network LLC